Setting up A Bathtub
Setting up A Bathtub
Blog Article
What are your thoughts concerning How to Install a Bathtub?
Mounting a tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a reasonably tough project. If the old bathtub is easily accessible, the project can move easily; if you have to open a wall surface to remove the old bathtub as well as place the new bathtub, the job is much harder. In either instance, the project is within a residence handyman's skills, although you will certainly need an assistant to leave the old tub as well as set in the brand-new one. Make sure you have actually qualified on your own for the work as well as are comfortable trying it. Rather than working with a professional to take control of a halfway-completed project, it is much better to consider utilizing one before you begin. Opportunities are you may require a professional plumber to make tube links.
This article will certainly aid you set up a brand-new bathtub in your shower room if you have actually already acquired a brand-new tub and don't require to change the plan of your previous water supply pipes.
Your devices and material list should make up the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you should do is detach the supply of water. After doing so, switch on the faucets to drain any type of water staying in the system. The procedure of removing the existing taps can be rather bothersome due to the restricted gain access to that is usually the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a cloth prepared for the staying water that will certainly originate from the pipelines. Once the supply pipelines have actually been removed, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this process. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any kind of old securing substance.
Prior to going on to fit the brand-new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin making sure that the washers are in place between the faucet and also the sink. Secure the tap in position with the supplier given backnut. When the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap connectors. The previous kind must be linked to the tap finishes initially, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Tub
Using both wood boards under its feet, position the tub in the needed position. The wood boards are practical in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 small factors.
The following objective is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bath tub up until the spirit level reviews degree.
To install faucets, fit all-time low of the outermost flexible faucet port to the appropriate supply pipeline by making a compression join; after that do the exact same for the various other tap.
Switch on the water system and examine all joints as well as new pipework for leakages as well as tighten them if necessary. Load the bathtub as well as also examine the overflow outlet and also the typical electrical outlet for leaks.
Ultimately, fix the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the tub needs to wait up until the bath tub has been made use of at least when as this will resolve it into its last position.
Preparing for the Installation
To start with, the supporting framework provided with the bath needs to be fitted (if required) according to the maker's instructions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to ensure that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets unit to avoid stress on the bath tub.
Fit the flexible tap adapters to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently prepare to be fitted in its final setting.
Tiling Around the Bath tub
In the location where the bath meets the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to break a stiff seal, triggering the water to pass through the wall surface between the bath as well as the tiling, causing issues with wetness as well as possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also fittings. They are sold in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the tub with water prior to securing, to enable the activity experienced when the bathtub is in use. The sealant can fracture rather very early if you do not take into consideration this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that content about How to Install a Bathtub while doing research the web. Sharing is nice. You won't know, you may just be helping someone out. Thank-you for taking the time to read it.
About This
Report this page